.

0 (hodnocen0 x )

EB

ONLINE

Cham : Springer International Publishing AG, 2021

1 online resource (449 pages)

ISBN 9783030705664 (electronic bk.)

ISBN 9783030705657

Lecture Notes in Mechanical Engineering Ser.

Print version: Roucoules, Lionel Advances on Mechanics, Design Engineering and Manufacturing III Cham : Springer International Publishing AG,c2021 ISBN 9783030705657

Intro -- Preface -- Organization Committee JCM 2020 Members -- Conference Chair -- Conference Program Chair -- Conference Advisory Chairmen -- Scientific Committee -- Organizing Committee -- Contents -- Manufacturing Engineering -- Designing Powder Metallurgy Process - The Influence of High Sintering Temperature on Dimensional and Geometrical Precision -- 1 Introduction -- 2 Experimental Procedure -- 3 Results and Discussion -- 3.1 Dimensional Precision -- 3.2 Geometrical Precision -- 4 Conclusions -- References -- Process Parameters Effect on Weld Beads Geometry Deposited by Wire and Arc Additive Manufacturing (WAAM) -- 1 Introduction -- 2 Experimental Setup -- 3 Results and Discussion -- 3.1 Temperature Evolution -- 4 Geometry Evolution -- 5 Conclusion -- References -- A Parametric Study of Additive Manufacturing Process: TA6V Laser Wire Metal Deposition -- 1 Introduction -- 2 Protocol of Experiments -- 2.1 Model and Variables -- 2.2 Methods -- 2.3 Taguchi’s Experimental Design -- 3 Results and Analysis -- 3.1 Correlation Coefficient -- 3.2 Variance Analysis -- 4 Conclusion -- References -- Develop Model for Controlled Depth Milling by Abrasive Water Jet of Ti6Al4V at Jet Inclination Angle -- 1 Introduction -- 2 Proposed Model with the Inclination Angle of the Jet -- 3 Experiment -- 4 Result -- 5 Conclusion -- References -- Simulation and Experimental Validation of Secondary Dendrite Arm Spacing for AlSi7Mg0.3 Chassis Parts in Low Pressure Die Casting -- 1 Introduction -- 2 Secondary Dendrite Arm Spacing Analysis -- 2.1 Low Pressure Die Casting Simulation -- 2.2 Spectrochemical Analysis with Optical Emission Spectroscopy -- 2.3 SDAS Mapping Through Micrographs -- 2.4 Correlation Between Measured and Simulated SDAS -- 3 Experiments and Simulation Analysis on Case Studies -- 4 Conclusions -- References.

2 Aim and Scope -- 3 Inventive Design Solution Concepts -- 3.1 Inventive Design Definition.

4 Conclusions -- References.

Simulation of Dynamic Stresses on High Performance Engine Valve Spring System Considering Coil Clashing Effect -- 1 Introduction -- 2 Testing Equipment -- 3 Multibody Dynamic Models -- 4 Finite Element Dynamic Model -- 5 Results -- 6 Conclusion -- References -- Thread Couplings Stress Analysis by Radial Basis Functions Mesh Morphing -- 1 Introduction -- 2 Discretized Models -- 3 Parameterization -- 4 Results and Discussion -- 5 Conclusions -- References -- Computer-Aided Tolerancing Analysis of a High-Performance Car Engine Assembly -- 1 Introduction -- 2 Method -- 3 Case Study: V12 Engine Assembly -- 4 Discussion and Conclusions -- References -- Review of Product Design and Manufacturing Methods for Prosumers -- 1 Introduction -- 2 Methodological Description -- 3 Results -- 4 Conclusions -- References -- State of the Art for Evaluation of Inventive Design Solution Concepts -- 1 Introduction ---

3 Conclusions and Perspectives -- References -- Topological Optimization of a Mechanical System with Adaptive Convergence Criterion -- 1 Introduction -- 2 The TOMS Method -- 3 Adaptive Coefficient of Convergence F -- 4 Conclusion and Perspectives -- References -- Design for Additive Manufacturing of a Topology Optimized Brake Caliper Through CAD-Platform-Based Systematic Approach -- 1 Introduction -- 2 Method -- 3 Case Study -- 3.1 Product Planning -- 3.2 Design -- 4 Results and Discussion -- References -- Product and System Engineering -- Evaluation of the Effects Caused by Mandibular Advancement Devices Using a Numerical Simulation Model -- 1 Introduction and Literature Review -- 2 Materials and Methods -- 2.1 Anatomical Model -- 2.2 Materials -- 2.3 Boundary Conditions -- 2.4 Meshing -- 3 Results and Discussions -- 4 Conclusions -- References ---

5 Phase III and IV: Development and Prototyping -- 6 Conclusions -- References -- A Well-to-Wheel Comparative Life Cycle Assessment Between Full Electric and Traditional Petrol Engines in the European Context -- 1 Introduction -- 2 Materials and Methods -- 3 Results and Discussion -- 4 Conclusions -- References -- Product Eco-Design in the Era of Circular Economy: Experiences in the Design of Espresso Coffee Machines -- 1 Introduction -- 2 Product Eco-Design for Coffee Machines -- 3 Case Studies -- 4 Conclusions -- References -- A Novel Procedure to Design a Positionable and Stable Drilling Template for Spine Surgery -- 1 Introduction -- 2 Methodology -- 3 Conclusion -- References -- CAD and Interaction -- Feature-Based Modelling of Laryngoscope Blades for Customized Applications -- 1 Introduction -- 2 Materials and Methods -- 2.1 Parametrization ---

Influence of the Hole Surface Integrity on the Fatigue Strength of an Aluminium Drilled Part -- 1 Introduction -- 2 Experimental Work -- 2.1 Fatigue Tests -- 2.2 Surface Integrity Characterization -- 3 Discussion and Conclusions -- References -- Cold Working Process on Hard Metal Stacked Assembly -- 1 Introduction -- 2 Stacked Cold Expansion Process -- 3 Experimental Campaign -- 4 Results -- 5 Conclusion and Perspectives -- References -- Numerical Simulation and Experimentation of Additive Manufacturing Processes with Polyurethane Foams -- 1 Introduction -- 2 Foam Polyurethane Characterization -- 3 Comparison Between Experiments and Numerical Simulation -- 4 Use of Simulation to Apply a Speed Correction on a Trajectory in Order to Minimize the Form Defect -- 5 Perspectives -- 6 Conclusion -- References ---

2 Aim and Scope -- 3 Inventive Design Solution Concepts -- 3.1 Inventive Design Definition.

2.2 Parametric Modelling -- 2.3 Mechanical Tests -- 2.4 Additive Manufacturing of a Laryngoscope Prototype -- 3 Results and Discussion -- References -- Magnitude Finger Forces Analysis During Simulating Pseudo-Haptic Spring -- 1 Introduction -- 2 Experimental Protocol and Participants -- 3 Results and Discussion -- 4 Conclusion -- References -- Parametric Hull Design with Rational Bezier Curves -- 1 Introduction -- 2 Design Approach -- 3 Case Study -- 4 Conclusion -- References -- A Framework for Curvature-Based CAD Mesh Partitioning -- 1 Introduction -- 2 Related Work -- 3 Curvature-Based Framework for ISO GPS Partitioning -- 3.1 Initial Region Partition -- 3.2 Region Refinement -- 4 Case Study -- 5 Conclusion -- References -- A Topology Optimization Method for Stochastic Lattice Structures -- 1 Introduction -- 2 Materials and Methods -- 2.1 The Algorithm -- 2.2 The Case Study -- 3 Results and Discussion ---

Analysis of Warpage Induced by Thick Copper Metal on Semiconductor Device -- 1 Introduction -- 2 Sample and Test Description -- 3 Warpage Measurements -- 4 Finite Element Model -- 5 Conclusions -- References -- Finite Element Modeling and Validation of Metal Deposition in Wire Arc Additive Manufacturing -- 1 Introduction -- 2 Proposed FE Metal Deposition Technique -- 2.1 Metal Deposition Modelling -- 2.2 Heat Input Modelling -- 2.3 Model Update -- 3 Validation -- 3.1 Results -- 4 Conclusions -- References -- Study of the Use of Sawdust and Mycelium Composite as a Substitute of EPS -- 1 Introduction -- 2 Materials and Methods -- 3 Results and Discussion -- 4 Conclusions -- References -- Topology Optimization Design of Internal Reinforcements in a Sailing Dinghy -- 1 Introduction -- 2 Methods -- 3 Case Study -- 3.1 Discussion -- 4 Conclusions -- References ---

Simulation of Dynamic Stresses on High Performance Engine Valve Spring System Considering Coil Clashing Effect -- 1 Introduction -- 2 Testing Equipment -- 3 Multibody Dynamic Models -- 4 Finite Element Dynamic Model -- 5 Results -- 6 Conclusion -- References -- Thread Couplings Stress Analysis by Radial Basis Functions Mesh Morphing -- 1 Introduction -- 2 Discretized Models -- 3 Parameterization -- 4 Results and Discussion -- 5 Conclusions -- References -- Computer-Aided Tolerancing Analysis of a High-Performance Car Engine Assembly -- 1 Introduction -- 2 Method -- 3 Case Study: V12 Engine Assembly -- 4 Discussion and Conclusions -- References -- Review of Product Design and Manufacturing Methods for Prosumers -- 1 Introduction -- 2 Methodological Description -- 3 Results -- 4 Conclusions -- References -- State of the Art for Evaluation of Inventive Design Solution Concepts -- 1 Introduction ---

State of the Art on Robust Design Methods for Additive Manufacturing -- 1 Introduction -- 2 State of the Art -- 2.1 Robust Design -- 2.2 Robust Design for Additive Manufacturing.

3 Conclusions and Perspectives -- References -- Topological Optimization of a Mechanical System with Adaptive Convergence Criterion -- 1 Introduction -- 2 The TOMS Method -- 3 Adaptive Coefficient of Convergence F -- 4 Conclusion and Perspectives -- References -- Design for Additive Manufacturing of a Topology Optimized Brake Caliper Through CAD-Platform-Based Systematic Approach -- 1 Introduction -- 2 Method -- 3 Case Study -- 3.1 Product Planning -- 3.2 Design -- 4 Results and Discussion -- References -- Product and System Engineering -- Evaluation of the Effects Caused by Mandibular Advancement Devices Using a Numerical Simulation Model -- 1 Introduction and Literature Review -- 2 Materials and Methods -- 2.1 Anatomical Model -- 2.2 Materials -- 2.3 Boundary Conditions -- 2.4 Meshing -- 3 Results and Discussions -- 4 Conclusions -- References ---

3.2 Our Position in Inventive Design Process -- 3.3 Inventive Design Solution Concept Evaluation -- 3.4 Research Gaps in Inventive Design Solution Concept Evaluation -- 4 Conclusion and Future Research -- References -- Systemic Approach for Local Energy Mix Assessment -- 1 Introduction -- 2 Methodology -- 2.1 Simulation -- 2.2 Control Strategies -- 3 Case Study -- 4 Conclusion -- References -- Towards a Better Understanding of Open Source Hardware Design Reuse in Company-Community Collaboration -- 1 Introduction -- 2 Design Reuse in Company and Community -- 2.1 Design Reuse in Companies -- 2.2 Design Reuse in Communities -- 3 Design Reuse in Company-Community Collaboration -- 4 Conclusions -- References -- Comfort Driven Redesign: The Case of Library Chairs -- 1 Introduction -- 2 Materials and Method -- 2.1 Design from Experiment -- 2.2 Redesign of Library Chair -- 2.3 Experiment Setup -- 2.4 Participants -- 2.5 Questionnaires -- 2.6 Experiment Protocol -- 3 Results -- 4 Conclusions -- References -- Constraint Analysis and Optimization of NES System Based on Variable Pitch Spring -- 1 Introduction -- 2 NES Design Process -- 3 Nonlinear Constraint Analysis -- 4 Optimization Result -- 5 Conclusions -- References -- Generative Design in the Transmission System of a Skateboard -- 1 Introduction -- 2 Materials and Methods -- 3 Results -- 4 Discussion -- 5 Conclusions -- References -- Methodology of Product Sustainable Redesign. Case Study: Furniture of a Clothing Retail Store -- 1 Introduction -- 2 Methodology -- 3 Case Study -- 4 Conclusions -- References -- Enhanced Material-Driven Design Methodology: Luffa Cylindrica’s Case -- 1 Introduction -- 2 Methodology -- 3 Phase I: Luffa Cylindrica Understanding -- 3.1 Volumetric Characterization -- 3.2 Mechanical Characterization -- 3.3 Other Properties -- 4 Phase II: Conceptualization.

5 Phase III and IV: Development and Prototyping -- 6 Conclusions -- References -- A Well-to-Wheel Comparative Life Cycle Assessment Between Full Electric and Traditional Petrol Engines in the European Context -- 1 Introduction -- 2 Materials and Methods -- 3 Results and Discussion -- 4 Conclusions -- References -- Product Eco-Design in the Era of Circular Economy: Experiences in the Design of Espresso Coffee Machines -- 1 Introduction -- 2 Product Eco-Design for Coffee Machines -- 3 Case Studies -- 4 Conclusions -- References -- A Novel Procedure to Design a Positionable and Stable Drilling Template for Spine Surgery -- 1 Introduction -- 2 Methodology -- 3 Conclusion -- References -- CAD and Interaction -- Feature-Based Modelling of Laryngoscope Blades for Customized Applications -- 1 Introduction -- 2 Materials and Methods -- 2.1 Parametrization ---

Generative Design for Additively Manufactured Textiles in Orthopaedic Applications.

Influence of the Hole Surface Integrity on the Fatigue Strength of an Aluminium Drilled Part -- 1 Introduction -- 2 Experimental Work -- 2.1 Fatigue Tests -- 2.2 Surface Integrity Characterization -- 3 Discussion and Conclusions -- References -- Cold Working Process on Hard Metal Stacked Assembly -- 1 Introduction -- 2 Stacked Cold Expansion Process -- 3 Experimental Campaign -- 4 Results -- 5 Conclusion and Perspectives -- References -- Numerical Simulation and Experimentation of Additive Manufacturing Processes with Polyurethane Foams -- 1 Introduction -- 2 Foam Polyurethane Characterization -- 3 Comparison Between Experiments and Numerical Simulation -- 4 Use of Simulation to Apply a Speed Correction on a Trajectory in Order to Minimize the Form Defect -- 5 Perspectives -- 6 Conclusion -- References ---

001895572

express

(Au-PeEL)EBL6567088

(MiAaPQ)EBC6567088

(OCoLC)1255220854